| Price | USD |
| MOQ | 1 PCS |
| Delivery Time | 3-5 days |
| Brand | Honeywell |
| Place of Origin | USA |
| Model Number | 3200-C0-000R-210-00000-E0-0 |
| Payment Terms | T/T |
| Brand Name | Honeywell | Payment Terms | T/T |
| Condition | Original New | Place of Origin | USA |
| Warranty | 12 Months | Shipping term | DHL/TNT/UPS/FEDEX etc. |
| Price | USD | Delivery Time | 3-5 days |
| Minimum Order Quantity | 1 PCS | Model Number | 3200-C0-000R-210-00000-E0-0 |
Pre-installation
Information
If
the
controller
has
not
been
removed
from
its
shipping
carton,
inspect
the
carton
for
damage
then
remove
the
controller.
•
Inspect
the
unit
for
any
obvious
shipping
damage
and
report
any
damage
due
to
transit
to
the
carrier.
•
Make
sure
a
bag
containing
mounting
hardware
is
included
in
the
carton
with
the
controller.
•
Check
that
the
model
number
shown
on
the
inside
of
the
case
agrees
with
what
you
have
ordered.
Model
Number
Interpretation
Write
your
controller’s
model
number
in
the
spaces
provided
below
and
circle
the
corresponding
items
in
each
table.
This
information
will
also
be
useful
when
you
wire
your
controller.
Mounting
Physical
Considerations
The
controller
can
be
mounted
on
either
a
vertical
or
tilted
panel
using
the
mounting
kit
supplied.
Adequate
access
space
must
be
available
at
the
back
of
the
panel
for
installation
and
servicing
activities.
•
Overall
dimensions
and
panel
cutout
requirements
for
mounting
the
controller
are
shown
in
Figure
2-2.
•
The
controller’s
mounting
enclosure
must
be
grounded
according
to
CSA
standard
C22.2
No.
0.4
or
Factory
Mutual
Class
No.
3820
paragraph
6.1.5.
•
The
front
panel
is
moisture
rated
NEMA3
and
IP55
rated
and
can
be
easily
upgraded
to
NEMA4X
and
IP66.
Mounting
Method
Before
mounting
the
controller,
refer
to
the
nameplate
on
the
outside
of
the
case
and
make
a
note
of
the
model
number.
It
will
help
later
when
selecting
the
proper
wiring
configuration.
1
Mark
and
cut
out
the
controller
hole
in
the
panel
according
to
the
dimension
information
in
Figure
2-2.
2
Orient
the
case
properly
and
slide
it
through
the
panel
hole
from
the
front.
3
Remove
the
mounting
kit
from
the
shipping
container
and
install
the
kit
as
follows:
•
For
normal
installation
two
mounting
clips
are
required.
Insert
the
prongs
of
the
clips
into
the
two
holes
in
the
top
and
bottom
center
of
the
case
•
For
water-protected
installation
four
mounting
clips
are
required.
There
are
two
options
of
where
to
install
the
mounting
clips:
1)
Insert
the
prongs
of
the
clips
into
the
two
holes
on
the
left
and
right
side
of
the
top
and
bottom
of
the
case
or
2)
on
the
center
on
each
of
the
four
sides.
•
Tighten
screws
to
2
lb-inch
(22
N•cm)
to
secure
the
case
against
the
panel.
CAUTION:
Over
tightening
will
cause
distortion
and
the
unit
may
not
seal
properly.
4
For
water-protected
installation,
install
four
screws
with
washers
into
the
four
recessed
areas
in
the
corners
of
the
front
bezel
(Figure
2-3).
Push
the
point
of
the
screw
through
the
center
piercing
the
elastomeric
material
and
then
tighten
screws
to
5
lb-in
(56
N•cm).
Ironman Technology Co.,LTD
Featured
Brand:
●
HONEYWELL
●
AB
●
OMRON
●SIEMENS
●SCHNEIDER
● ROSEMOUNT● ABB ● NOTIFIER ●MTL ● GE ●And many more !
Honeywell UDC3200 Controller 3200-C0-000R-210-00000-E0-0 Universal Digital Controller
Lead time:3-5 days
New with one year warranty
